Posted in

how to test a linear displacement sensor

If you’ve ever worked in manufacturing, aerospace, automation, or even medical device assembly, you’ve relied on linear displacement sensors—those unassuming devices that turn straight-line movement into measurable, reliable data. As a linear displacement sensor supplier, I’ll tell you straight: the best sensors in the world are useless if they don’t meet your application’s exact needs, and testing them before installation isn’t just a quality step—it’s a cost-saving lifeline. Over 12 years in this field, I’ve seen customers scrap entire production runs because they skipped simple sensor testing, and I’ve also helped a aerospace client avoid a $2M retrofit by catching a calibration drift before their critical part was installed. Today, I’m walking you through the hands-on, science-backed testing process we use here—no jargon, no fluff, just the steps that will keep your projects on track. Linear Displacement Sensor

First, let’s get on the same page about what we’re testing. Linear displacement sensors (LDS) come in three core types, and each needs slightly adjusted test criteria: potentiometric (wiper-based, often for low-cycle general automation), LVDT (linear variable differential transformer, non-contact, for high-precision, high-cycle aerospace/medical), and magnetostrictive (combines non-contact and long-range, for factory robotics). No two applications demand the same test parameters, so your first step before grabbing tools is to map your use case: what’s the full travel range you need? What’s the maximum cycle speed? Is the environment dirty, wet, extremely hot, or cold? What tolerance are you working to—±0.1mm for a press brake, or ±1mm for a conveyor belt? This baseline will be your test checklist, not a generic “pass/fail” list.

Let’s start with the most fundamental test, and the one most people skip at their peril: mechanical functional testing. This is the hands-on check that ensures the sensor physically moves, connects, and registers data without binding or damage. Start with mounting: even a tiny misalignment (1mm off-center) can throw readings off by 5% or more, so mount your LDS per the manufacturer’s specs—we always specify a rigid mounting bracket with clearance to avoid stress on the sensor’s body, because stress on the core is a silent killer of long-term accuracy. Next, simulate full travel: slowly move the sensing element across its entire rated linear range, not just a middle section. For a 100mm travel sensor, move it from 0mm to 100mm, hold at 0mm, then reverse to 50mm, 100mm, and back to 0mm twice. Pay attention to two things: first, does the movement feel smooth, with no sticky points or grinding? For wiper sensors, a tiny bit of resistance is normal, but if it stops mid-travel, that’s a sign of a faulty wiper or misalignment. For non-contact LVDT and magnetostrictive sensors, there should be zero drag—any friction here means a misaligned core or magnet, which will degrade accuracy over time. Second, do all your motion commands register correctly on your readout device? If you move the sensor 20mm, but the readout shows 18mm, that’s a mechanical issue, not an electrical one—easy to fix early, way harder to fix mid-install. I once had a small food processing customer bring back 12 potentiometric sensors because they skipped this step and found half would lock up after 5mm of travel; a quick recheck showed a wiper was bent in shipping, and a $10 part swap saved them a $15k installation job.

Next up, electrical performance testing—this is where we measure the sensor’s core accuracy, the number one thing people worry about. Let’s break this into two parts: static accuracy (how well it measures a single position) and dynamic accuracy (how well it tracks movement over time, which is critical for high-speed applications). For static accuracy, you need a calibrated reference that’s at least 10x more accurate than the sensor you’re testing—no shortcuts here. We use digital calipers with ±0.005mm tolerance for small precision sensors, and laser linear encoders for long-range industrial models (those have ±0.01mm/m accuracy, so they’re trusted in calibration labs). Here’s how to run the test: set your LDS to its minimum travel position (let’s call that 0mm), stabilize the reference, and record the sensor’s reading. Then move the sensor in 10% increments across its full travel range—for a 100mm sensor, that’s 10, 20, …, 100mm. At each point, hold the sensor steady for 3 seconds to eliminate any motion lag, then record both the LDS reading and the reference reading. The difference between these two numbers is your static error. Most industrial applications accept ±0.1% of full-scale reading (FOS) error, so a 100mm sensor can have up to 0.1mm error and still be usable— aerospace clients, though, demand ±0.05% FOS, so we have to bump that tolerance. What’s a red flag here? If the error isn’t linear—meaning it jumps from 0.05mm at 10mm to 0.2mm at 100mm—that’s a sign of a faulty signal conditioning circuit, or a core alignment issue in LVDTs.

Now dynamic accuracy, which is often overlooked but make or breaks high-cycle applications like robotic welding or packaging lines. Dynamic accuracy measures how well the sensor tracks a moving target, because static testing only checks stationary positions. To test this, you’ll need a motion controller that can move the LDS (or the target it’s sensing) at controlled speeds, from slow to its maximum rated cycle speed (for example, 100mm/sec to 1000mm/sec). Pair it with that same calibrated laser encoder, and run the same 0 to 100mm travel cycle 10 times at each speed. For each cycle, calculate the difference between the LDS reading and the reference at every 10mm interval. The key here is to check for hysteresis—this is the difference in reading when moving to a position vs. moving away from it. A small amount of hysteresis (≤0.02% FOS) is normal, but if it climbs to 0.1mm at 1000mm/sec, that means your sensor’s signal processing is too slow, or you’ve picked a sensor with too low a bandwidth for your application. Last year, we had a robotics customer come to us with a sensor that was dropping readings during high-speed pick-and-place; their old test only checked static accuracy, but our dynamic test showed 0.3mm hysteresis at 800mm/sec—we swapped it for a high-bandwidth magnetostrictive sensor, and their error dropped to 0.05mm.

Once you’ve nailed mechanical and electrical tests, you need to validate environmental robustness, because a sensor that works in a lab will fail in a hot, dirty factory floor or a cold freezer. This test is application-specific, but here are the standard checks we do for our full-range testing: temperature testing, IP rating testing, and cycle life testing. For temperature testing, put the sensor in an environmental chamber, cycle it from -40°C (for aerospace or cold storage) to 85°C (for factory automation), hold it at each extreme for 2 hours, then run the full mechanical and electrical tests. If the error jumps more than 0.15% FOS at either end, the sensor’s internal components are not temperature-stabilized, and will fail over time. For IP (Ingress Protection) testing, if your sensor is going near water, dust, or washdown areas, test it with a water jet (IP67) or submersion (IP68) per IEC 60529 standards. We test our washdown-rated sensors by spraying them with high-pressure soapy water for 10 minutes, then checking for water intrusion or reading errors—any sensor that fails this gets sent back to our engineering team to fix the seal. Cycle life testing is for high-use applications: run the sensor through its full travel range at maximum speed 1 million times, then recheck accuracy. A good LDS will retain 90% of its initial accuracy after 1 million cycles; if it drops below that, the internal wiper (for potentiometric) or core (for non-contact) is wearing out too fast, which will lead to unplanned downtime.

The final step in testing is real-world field validation, and this is the most important one you can do—lab tests are great, but nothing beats testing the sensor in your exact setup. We always recommend our customers run a 2-week pilot: install a test sensor on a single production line or machine, run it through normal operations, and log data continuously. Watch for things like signal noise (that’s random fluctuations in readings when there’s no movement) or drift (slow, steady change in readings over time without movement). I once had a medical device customer that passed all lab tests, but their pilot showed 0.2mm of drift after 7 days—turns out their assembly line had a magnetic field that was interfering with their LVDT sensor; swapping to a magnetostrictive sensor fixed the issue, and we never would have caught that in a static lab test.

Now, a few common pitfalls to avoid when testing LDS, from years of seeing customers make these mistakes. First, don’t skip reference calibration: if your calipers or encoder are off, your test data is useless. We calibrate our reference tools every 6 months per ISO 17025 standards, and we tell all our customers to do the same. Second, don’t test only at room temperature: 70°F is great for lab work, but if your sensor will live in a 120°F foundry, that’s a whole different ballgame. Third, don’t ignore electrical interference: if your sensor is near a motor, PLC, or power cable, run a noise test by turning on all nearby equipment and checking for reading fluctuations—shielded cables can fix a lot of these issues, but you need to test for it upfront.

At the end of the day, testing a linear displacement sensor isn’t about checking boxes—it’s about making sure the sensor you buy is built to fit your specific needs, not just a generic spec sheet. As a linear displacement sensor supplier, we stand behind our products, which is why every sensor we ship goes through 100% of these tests before it leaves our facility, not just a random sample. If you’re tired of dealing with sensors that fail mid-project, or you need help building a custom testing plan for your unique application, don’t hesitate to reach out to our team to discuss your requirements and connect with our sales department to explore solutions.

Pressure Sensor Core References
IEC 60529: Degrees of Protection Provided by Enclosures (IP Code)
ISO 17025: General Requirements for the Competence of Testing and Calibration Laboratories
LVDT Theory and Application, McGraw-Hill, 2019
Magnetostrictive Sensor Technology for Industrial Automation, Sensor Magazine, 2021


Shanghai Zhaohui Pressure Apparatus Co., Ltd.
Shanghai Zhaohui Pressure Apparatus Co., Ltd. is one of the most professional linear displacement sensor manufacturers and suppliers in China, featured by quality products and good service. Please rest assured to wholesale advanced linear displacement sensor in stock here from our factory. Also, customized service and 1 year warranty are available.
Address: 2-6/F, Building 8, No.115, Lane 1276, Nanle Road, Shanghai, China
E-mail: sensorsales@zhyqsensor.com
WebSite: https://www.sinosensor.net/